• <pre id="wluqd"></pre>

        <dfn id="wluqd"></dfn>
        加入收藏 在線留言 聯系我們
        關注微信
        手機掃一掃 立刻聯系商家
        全國服務熱線19079192829
        公司新聞
        故障診斷和排除(二十三)珀金斯1104D-E44TA發動機總 售后保障
        發布時間: 2023-07-01 10:54 更新時間: 2024-11-01 17:00

        產品:     EXCAVATOR

        型號:    311B EXCAVATOR 2LS

        配置:   311B TRACK-TYPE EXCAVATORS 2LS00001-UP (MACHINE) POWERED BY 3064 ENGINE

        故障診斷和排除

        Air Conditioning and Heating R134a for All Caterpillar Machines

        Automatic Temperature Control Panel Troubleshooting - 584 and 584HD Forwarders

        SMCS - 7309-035-YC

        Automatic Temperature Control (ATC) - Fault Codes: (only for 584 Forwarders and 584HD Forwarders)                          Troubleshooting

        3925290567.jpg

        Illustration 1


        To display fault codes, depress the ON key three times in rapid succession. The digital display will then display any active fault codes. Pressing the ON key again repeatedly will scroll through any   existing error codes. After five seconds without further key presses, the system will exit the            diagnostics mode and return to normal operation.

        No Faults - E0

        Cab Sensor Shorted - E1

        3926126929.jpg

         

        Cab Sensor Open - E2

        Evaporator Probe Shorted - E3

        Evaporator Probe Open - E4

        Duct Sensor Shorted - E5

        Duct Sensor Open - E6

        Pressure Transducer Open - E151

        Pressure Transducer Shorted - E12

        Water Valve Actuator Error - E13

        Electronics or Comm. Error - E17

        Clutch Open - E18*

        Clutch Shorted - E19*

        No Refrigerant - E20*

        High-pressure - E22*

        Low Voltage Error - E23*

        * Future implementation

         

        Advanced Diagnostics:

        The ATC Advanced Diagnostics control panel allows the technician to see real-time system          information on the control panel display. Control panel display will assist in A/C-heater servicing. This real-time information can help the service technician diagnose certain system problems.

        To display advanced diagnostics, depress ON key three times in rapid succession (fault codes        displayed) then immediately press and hold ON key for five seconds. The text "CAB" will be        displayed. After a few seconds, the real-time value of the cab temperature measured by the ATC is displayed. This value, as well as any other value displayed by the control panel, will continuously update. Pressing the ON key again repeatedly will scroll through all of the available diagnostics     information

        CAB - Cab Air Temperature (°C or °F)

        EVAP - Evaporator Core Temperature (°C or °F)

        DUCT - Duct Air Temperature (°C or °F)

        HEAT - Water Valve Command (% of valve open)

        A-C - A-C Clutch Request (on / off )

        FAN - Blower Fan Speed (% of maximum fan speed)


         3927597620.jpg

        DEF - Defrost Mode Active (On/Off)

        HI-P - High Side Pressure (psig or bar)

        PRHT - Blower Enable Active (On/Off)

        VOLT - System Voltage (DC Volts)

        Note: The system can be operated normally while in advanced diagnostics mode, including        changing the temperature set point or changing the blower fan speed, to evaluate the response of the system.

         

        Firmware Version Mode

        The firmware version of the control panel and Electronic Control Unit (ECU) can be displayed.    From the advanced diagnostics mode, press and hold the ON key for five seconds. The text CTRL will be displayed and after a few seconds, the control panel firmware version number will be         displayed. Pressing the ON key will toggle to the ECU firmware version.

        The following firmware version information is available:

        CTRL - Control Panel Version

        ECU - ECU Version

        Exiting the Diagnostic Mode:

        To exit the advanced diagnostic mode or firmware Version mode, turn the system OFF by pressing the OFF key.

         

        Additional Troubleshooting:

         

        No Display

        ?  Turn on control panel with the ON key.

        ?  Check to see if the display Illuminates.

        ?  Verify that the control panel is plugged into the wire harness.

        ?  Check to see if wire harness is wired into vehicle properly.

         

        No Fan

        ?  Turn up fan with the fan UP key.

        ?  Make sure that the fan is plugged into wire harness, verify all wiring connections.

        ?  Verify that the circuit breakers or fuses are intact.

        ?  If all other functions work properly, replace ECU.


         

        ?  Turn up heat with the Temperature UP key. Use the advanced diagnostics to verify that the water valve is commanded open.

        ?  Inspect and verify all wiring connections.

        ?  Verify that any coolant shut off valves on the engine are open.

        ?  Verify that warm coolant is flowing into the heater core by testing the heater hoses.

        ?  Inspect and replace the electronic water valve if necessary.

        ?  Inspect and replace ECU if necessary.

         

        No Cooling

        ?  Turn down heat with the Temperature DOWN key and enable the defrost mode. Use the advanced diagnostics to verify that the A/C clutch is requested ON.

        ?  Verify that the system is fully charged with refrigerant.

        ?  Verify that voltage is present at the compressor clutch.

        ?  Verify that the correct voltage is present at the clutch relay on the wire harness.

        ?  Inspect and verify all wiring connections.

        ?  Inspect and replace clutch relay ifnecessary.

        ?  Inspect and replace refrigerant high-pressure and/or low-pressure cut out switches if necessary.

        ?  Inspect compressor and clutch assembly and replace clutch if necessary.

        The system is not controlling the cab temperature properly

        ?  Inspect the cab air temperature sensor.

        ?  Verify that the recirculation vent inlet is not obstructed. Inspect and replace recirculation vent air filter if necessary.

        ?  Inspect and replace recirculation vent air filter, if necessary.

        ?  Change the setpoint temperature in small increments.

        ?  Verify that the water valve is working properly. Refer "No Heat"(see No Heat).

        ?  Verify that the compressor clutch is working properly. Refer "No Cooling".

        The evaporator core is icing up and restricting airflow

        ?  Inspect the evaporator core probe.

        ?  Verify that the probe is making good contact with the evaporator fins and is not loosely inserted.


         

        ?  Reposition the probe and check the core temperature during operation using the advanced diagnostics.

        ?  Replace the evaporator core if necessary.

        主營品牌:卡特彼勒、沃爾沃、帕金斯、道依茨、三菱、奔馳

         

        卡特彼勒挖機型號:313D、320D、323D、326D、330D、329D、336D、349D、345D

        卡特彼勒型號:C1.1、C2.2、C4.4、C7.1、C9、C9.3、C13、C11、C15、C18、C27、3512、3512B、3516、3516B

         

        帕金斯:

         1104A-44、1104A-44T 、 1104C-44 、1104C-44 、 1104C-44TA 、 1104C-44TA 、1104C-44T、1104D-44、 1104D-44TA 、1104D-E44TA 、1106C-70TA、 1106D-70TA 、 1106D-E70TA 、1204E-E44TA、1204E-E44TTA 、1204F-E44TA 、1204F-E44TTA 、 1206E-E66TA 、 1206E-E70TTA 、 1206F-E70TA、2806J-E18TA 、2206、2506、403D-11 、403D-15、403D-17 、403F-07、403F-11G 、 403F-15G、 403F-15T、 404D-15、404D-22 、 404D-22T、404F-E22TA、404F-E22T、854E-E34TA 、854F-E34TA 、854F-E34T 、904J-E36TA 、4TMG、1004


        其他新聞

        聯系方式

        • 電  話:19079192829
        • 市場經理:鄧先生
        • 手  機:19079192829
        • 微  信:zzzx-3699